Connect Tech Blue Heat/Net Sync Manual de usuario descargar pdf (Pagina 12)

CONNECT TECH INC. www.connecttech.com

Xtreme/104 Radio Modem

WIT910 900 MHz Up to 20 miles Up to 86.4 Kbps 460 KHz 16 Byte FIFO

WIT2450 2.4 GHz Up to 5 miles

Up to 230.4 Kbps 864 KHz 16 Byte FIFO

WIT2410 2.4 GHz Roaming Up to 6 miles Up to 230.4 Kbps 750 KHz 16 Byte FIFO

Product Cirronet Frequency Operating I/O Data Rate Bandwidth UART

Model Range Range

At a Glance

SOLID STATE DRIVES FEATUREPAK

FlashDrive/104 is a flash based, solid state storage module designed

as a drop-in replacement for magnetic hard drives. High density memory

chips provide immense storage capabilities to ensure reduced latency

and faster data transfer. Requires no drivers.

FlashDrive/104

Form Factor

PC/104 - Supports all platforms and operating

systems

Capacity

4, 8, 16 or 32GB

Connector

Standard 40-pin, 100” and 2.5” - 44-pin, 2mm

Hard Disk ATA/IDE

Current Idle: 5 mA Read/Write Cycles: 150 mA

Temperature -40˚C to 85˚C (4, 8, 16 or 32GB models)

Power +5V DC (± 5%)

PC/104 WIRELESS RADIO MODEMS

Xtreme/104 Radio Modem

Xtreme/104 Radio Modem is cost-effective and reliable provides

wireless, long range communications for embedded PC/104 applications

This card incorporates Cirronet’s WIT910 900 MHz frequency hopping

spread spectrum technology which provides immunity to jamming and

multipath fading, ensuring transparent, robust communications.

Bus

PC/104

Power

Powered via PC/104 bus - requires only 5V DC

Temperature Operating temperature:

0˚C to 70˚C (32˚F to 158˚F)

Dimensions Width: 9.1 cm (3.6 inches)

Length: 9.7 cm (3.8 inches)

Height: 1.1 cm (0.44 inches)

Warranty One year limited

Xtreme/FP is a 4 port multi-port serial and digital/IO FeaturePak

Module designed to add four high speed serial ports and 16-bits of GPIO

to any FeaturePak compatible base board or single board computer.

Xtreme/FP

Ports

4 Ports RS-232

Connectors

IO connected to FeaturePak IO Pins

Temperature -40˚C to 85˚C (-40˚F to 185˚F)

Power 500mA

UART

PCI Express UART, 256 Byte FIFO

Baud

1 Mbps

Dimensions

2.550” x 1.7”

PCI Express to

FeaturePak Adapter

PCI Express to FeaturePak Adapter converts any FeaturePak Module

to PCI Express. This adapter supports any x1, x4, x8 or x16 lane PCI

Express slot. Simply mount the FeaturePak module to the adapter and

install the adapter into any PCI Express slot.

Connectors

2mm + .1” FeaturePak IO headers,

2x Micro B USB, JTAG, ATX Power, DB-9

Temperature -40˚C to 85˚C (-40˚F to 185˚F)

Features

Custom prototyping area

x1 lane PCI Express card edge allows installation in

any slot width (x1, x4, x8, x16)

Dimensions 4.350” x 6.000”

What is FeaturePak?

FeaturePak is a mezzanine-style standard designed to work with existing standards such as PC/104,

SUMIT, Qseven, ETX, XTX, COM Express, etc. FeaturePak modules are smaller than a credit card at

42mm x 65mm in size and make use of a low-cost connector to integrate all host and external I/O

interfaces. FeaturePak allows users to reconﬁgure system designs using oﬀ-the-shelf modules based on

an open standard that will ensure a strong eco-system.

Connect Tech’s FeaturePak products include Xtreme/FP, a 4 port multi-port serial and digital IO

FeaturePak module, and PCI Express to FeaturePak Adapter which converts any FeaturePak

Module to PCI Express.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 20 21

Comentarios a estos manuales

Sin comentarios

Connect Tech Blue Heat/Net Sync Manual de usuario Pagina 12

Comentarios a estos manuales